eSmooth Nature eSun filament

Description

eSmooth Nature eSun filament

details
1. It is translucent and white.
2. Non-toxic, tough, strong, not easily broken, good temperature resistance and creep resistance.
3. Low shrinkage
4. Easy to absorb moisture. The line should not have moisture before printing. You can use ethanol solution with a purity of more than 99.7% and spray polishing liquid.
5. Environmentally friendly, stable, will be brighter after polishing, complete decomposition, no carbonation residue and no residue at 600℃, can be used for metal casting.

Description about eSmooth:

1. eSmooth has a translucent, white appearance.

2. Non-toxic, tough, hard, hard to break, good temperature resistance and creep resistance.

3. Good print precision, no warping, stripping or stringing.

4. eSmooth is easy to absorb water, so better drying before print. Remember to choose an ethanol solution over 99.7% purity and work with a spray type polisher for polishing.

5. Environmentally friendly, stable performance, more refined and brighter after polishing, complete decomposition, no carbonation and no residue in 600 ℃, can be used for metal casting.

eSmooth printing parameters

  1. Best print temperature: 190-210℃
  2. Bed temperature: 45-55℃
  3. Feed rate: 30-90mm/s
  4. Idling speed: 90-150mm/s

Printing notices

  • Leveling printing plate before starting;
  • Heat the hot bed to 45~55℃ before printing, paste transparent golden polyimide high temperature resistance tape to the surface and keep it clean;
  • Keep a optimum distance between nozzle and plate (which allows you to paint out a flat line while moving your nozzles; if too far the line will be much mellow and too close will be hard to let filament out);
  • A lower filling rate can print finer articles (about 20%~ 30% degrees);
  • Nozzle diameter should be bigger than layer thickness. Try parameters like 0.2, 0.25, and 0.3;
  • No need to print in a closed area.

When polishing:

Hang the prints in the air to make a full contact with ethanol vapor. The whole process takes 20-30 minutes.

After polishing:

The prints normally turn white and soft. Just use tweezers or other tools for air drying. Do not touch bare hands.

To achieve best polishing effect, 3-5 days air drying will volatilize solvent on surface and form a hardened layer. Do not dry with oven, or the solvent will volatilize and destroy polishing effect.

Product form
Free pickup in our shop(s)

990.00 ฿

  • Shipped today? Order within: Jul 04, 2026 11:00:00 +0700
  • Fast Delivery
Chat on LINE and FB Messenger

Description

eSmooth Nature eSun filament

details
1. It is translucent and white.
2. Non-toxic, tough, strong, not easily broken, good temperature resistance and creep resistance.
3. Low shrinkage
4. Easy to absorb moisture. The line should not have moisture before printing. You can use ethanol solution with a purity of more than 99.7% and spray polishing liquid.
5. Environmentally friendly, stable, will be brighter after polishing, complete decomposition, no carbonation residue and no residue at 600℃, can be used for metal casting.

Description about eSmooth:

1. eSmooth has a translucent, white appearance.

2. Non-toxic, tough, hard, hard to break, good temperature resistance and creep resistance.

3. Good print precision, no warping, stripping or stringing.

4. eSmooth is easy to absorb water, so better drying before print. Remember to choose an ethanol solution over 99.7% purity and work with a spray type polisher for polishing.

5. Environmentally friendly, stable performance, more refined and brighter after polishing, complete decomposition, no carbonation and no residue in 600 ℃, can be used for metal casting.

eSmooth printing parameters

  1. Best print temperature: 190-210℃
  2. Bed temperature: 45-55℃
  3. Feed rate: 30-90mm/s
  4. Idling speed: 90-150mm/s

Printing notices

  • Leveling printing plate before starting;
  • Heat the hot bed to 45~55℃ before printing, paste transparent golden polyimide high temperature resistance tape to the surface and keep it clean;
  • Keep a optimum distance between nozzle and plate (which allows you to paint out a flat line while moving your nozzles; if too far the line will be much mellow and too close will be hard to let filament out);
  • A lower filling rate can print finer articles (about 20%~ 30% degrees);
  • Nozzle diameter should be bigger than layer thickness. Try parameters like 0.2, 0.25, and 0.3;
  • No need to print in a closed area.

When polishing:

Hang the prints in the air to make a full contact with ethanol vapor. The whole process takes 20-30 minutes.

After polishing:

The prints normally turn white and soft. Just use tweezers or other tools for air drying. Do not touch bare hands.

To achieve best polishing effect, 3-5 days air drying will volatilize solvent on surface and form a hardened layer. Do not dry with oven, or the solvent will volatilize and destroy polishing effect.

Frequently Asked Questions

  • eSmooth Nature eSun filament คืออะไร ใช้ทำอะไร?

    eSmooth Nature เป็นเส้นวัสดุธรรมชาติสำหรับใช้เป็น Support Material ที่ละลายได้ในน้ำ เหมาะสำหรับพิมพ์ร่วมกับ PLA บนเครื่อง Dual Nozzle ช่วยให้ถอด Support ออกได้ง่ายโดยไม่ทำลายชิ้นงาน

  • eSmooth ละลายในอะไร?

    eSmooth ละลายในน้ำอุ่น อุณหภูมิประมาณ 30–40°C แช่ชิ้นงานในน้ำอุ่น 30 นาทีถึง 2 ชั่วโมง ขึ้นอยู่กับความหนาของ Support

  • ต้องตั้งอุณหภูมิเท่าไหร่?

    อุณหภูมิหัวฉีด 190–215°C ฐานพิมพ์ 50–60°C ใกล้เคียงกับ PLA ทั่วไป เหมาะสำหรับใช้คู่กับ PLA บนเครื่อง Dual Extrusion

  • eSmooth ดีกว่า PVA อย่างไร?

    eSmooth มาจากวัสดุธรรมชาติ ย่อยสลายได้ดีกว่า PVA และมักมีอุณหภูมิพิมพ์ที่เสถียรกว่า เหมาะสำหรับผู้ที่ต้องการวัสดุ Support ที่เป็นมิตรกับสิ่งแวดล้อม

  • eSmooth Nature eSun filament เหมาะกับงานอะไรบ้าง?

    เหมาะสำหรับชิ้นงานที่มีโครงสร้างซับซ้อน ช่องโพรง Overhang สูง และรูปทรงที่ต้องการ Support ที่ยากต่อการถอดด้วยมือ

  • ควรเก็บ eSmooth อย่างไร?

    ต้องเก็บในถุงสุญญากาศพร้อมสารดูดความชื้นอย่างเคร่งครัด เนื่องจากดูดซับความชื้นได้สูงมาก หากดูดชื้นจะเปราะและพิมพ์ไม่ได้ ควรอบที่ 45–55°C นาน 4–8 ชั่วโมงก่อนใช้

  • ใช้กับเครื่องพิมพ์ Single Nozzle ได้ไหม?

    ไม่สามารถใช้ได้อย่างมีประสิทธิภาพสำหรับการเป็น Support Material บนเครื่อง Single Nozzle เพราะต้องพิมพ์แยกจาก Model Material ต้องใช้เครื่อง Dual Nozzle

  • หลังแช่น้ำแล้วชิ้นงานหลักเสียหายไหม?

    ไม่ PLA ไม่ละลายน้ำ ชิ้นงานหลักจะยังคงสภาพสมบูรณ์ หลังแช่น้ำจนละลาย Support ออกแล้ว ล้างชิ้นงานด้วยน้ำสะอาดและผึ่งให้แห้ง

Recently viewed products

Login

Forgot your password?

Don't have an account yet?
Create account